Tools for Lifters

To help lift and manipulate loads, we have a large selection of lifting tools that fit on our lifters. Since the lifting tool is also the end effector that interfaces with the load, it is crucial that it is designed correctly. In addition, it is also important that the lifting tool and lifter work perfectly together. Since we design both together, you as a customer are always sure to get a perfect match. Using the same principles as for our lifters, the lifting tools are strong and reliable. Built for industrial use and with a large degree of modularity, these lifting tools are often customized and will fit almost any load.

When a lifting tool needs to do more than just lift a load up and down, it becomes a manipulator. This is the case for tools such as our roll manipulator or rotation unit. These manipulators are manually or electrically powered, depending on the use and the load.
Some lifting tools simply need to lift a load up and down, such a fork or a platform. These we designate as non-manipulators.

Manual manipulators are lifting tools that in themselves can be turned, swung or otherwise moved by hand to help position the load.
Non-manipulators are simple lifting tools that support a load. Typically designed to accommodate a specific type of load, these tools are found in countless different versions.
Electrical manipulators are lifting tools that in themselves can be turned, swung or otherwise moved electrically to help position the load.


During lifting and handling operations safety should always be the first priority. By using our lifters you reduce the risk of back injury as well as other forms of injury sustained from manual lifting. To ensure operator safety in regard to using the lifter we of course adhere to all applicable industry standards and regulations. We conduct thorough risk evaluations and address the "what if"-scenarios that may lead to safety issues. We implement technical features such as safety clutches, overload protection, hold-to-run controls and emergency stops when applicable.
Finally, our factory testing procedures eliminate safety issues that might arise from assembly- or component errors.
In many lifting and handling operations safety also applies to the load in addition to the operator. Some of our customers use our lifters for loads with values exceeding 100.000 €. In general, dropping or damaging a load due to failure of handling equipment is not acceptable to us and this is of course reflected in our product. 


Our customers rely on our lifters. For instance, lifters supply machines and personnel with the materials needed during production. As such the lifters become an essential part of the chain of production, making reliability a key issue. We live up to these expectations by implementing the following in all our products:

  • We use only the highest quality components in our lifters. Quality is always the first priority in component selection with no compromises allowed.
  • The lifters are dimensioned for a 20 year life expectancy assuming normal use (excluding wear and tear elements such as wheels and batteries).
  • During design, calculations are made to ensure that all safety factors for strength exceed industry standards by a comfortable margin. Apart from the added user safety, this also ensures an added degree of reliability.
  • We test everything rigorously before it leaves our facility. We document all tests with photos, video and check lists. 


Lifting equipment defies its purpose if the user risks injury or MSDs (Musclouskeletal Disorders) by using it. As such, we make in depth analyses of how users interact with our lifters and make sure our design process takes all ergonomic issues into consideration.
Our lifting solutions deliver a large number of electrically power functions, which reduces the need for repetitive manual cranking or pedal/pump motions. Control of the powered functions is done with at custom designed remote control with large buttons, which are easy to press even with gloves on. The remote allows for an optimal position for the user during lifting an manipulating operations.
All handles are places and designed based on ergonomic principles to avoid incorrect motion and unnecessary strain. The necessary force to manoeuvre the lifter is considered and wheels and castors are selected carefully in accordance (based on the load placement and the surface, which they will be used on).

Custom Solutions

The parameters for lifting and handling operations vary widely. Loads vary in geometry and weight, the direction and type of manipulation varies depending on the task at hand and access is often restricted by doors, ceilings, machine parts and other obstructions.
When we designed our lifters we knew that in many circumstances a standard solution would not do. So, we adopted a modular approach allowing for easy customisation of all major dimension of our lifters. Apart from custom dimensions we also deliver a wide variety of other options including stainless variates, waterproofing (IP65), ATEX and Electrostatic discharge (ESD).
With any custom solution, communication during the design phase is critical. We have many years experience with this and have a standardised procedure to ensure the best possible result. See more on this and our custom solutions in general here.

Reliability and Maintenance

Our modular design approach allows for easy customisation of our lifters, but also has the added benefit of allowing easy maintenance. For instance, removing and replacing a lifting column is achieved by only loosening a few screws. The same goes for the entire control unit. Unscrew two screws and in many cases the complete motor and gear unit can be replaced. We know that our customers rely on our lifters and as such easy maintenance and reliability are critical.

Lifter Components

When we designed our lifters, we carefully tried and tested a large variety concepts and components to ensure that we built the optimal lifter. Below is short description of each of the major components and what made us choose them. If you have any questions regarding our lifters, please don't hesitate to contact us here.

Lifting Column Cropped

Lifting Column

The lifting column is the main mechanical feature in any lifter and hence of critical importance. In the design we use, the major components are: C-profile, carriage, cambelt and gearwheel. The C-profile of the lifting column is made in one piece by laser cutting and bending using CNC-technology. This ensures strength and precision.

Zoom Sledge 3


Designed around a tube geometry, this carriage is designed for strength and reliability. The use of large bearings with POM-wheels ensures smooth and quiet operation. And unlike most competitors we also use bearings on the side of the carriage to make sure that off-centre loads do not interfere with lifting.


AT10 Circle

Cam Belt

Power is transferred to the sledge via a cam belt. The use of a cam belt ensures smooth motion and maintenance free operation. The cam belt consist of a matrix of numerous steel wires encased in a polyurethane body. Unlike a chain, where a single bad plate or pin can be catastrophic, failure of a single wire will not cause breakage. This, along with a safety factor of 10, ensures that we have never experienced belt failure.

Zoom Gear whell

Gear Wheel with One-way Clutch

At the lower end of the lifting column, a gear wheel, powered by a motor, drives the cam belt. A one-way clutch ensures that the lifter cannot force the lifting tool down. This prevents tipping and crushing and also provides an easy way of placing loads on surfaces in one smooth motion. To ensure long life and safety, we use only the best German-made one-way clutches available.

Zoom Wheel 2


The choice of wheels and casters on a lifter is obviously critical with regard to mobility; in addition the choice of braking system has an impact on security. We have literally tested hundreds of different kinds of wheels to ensure that we give our customers the best options. Depending on the surface on which the lifter will be used and the type of application, we advise our customers as to which choice in wheels is best.

Zoom Motor


To power our lifters, we use high quality 24V DC permanent magnet motors, built in the EU. Fitted on self-locking worm gears with all metal parts, these are safe and reliable, unlike cheap alternatives with nylon gears.

Legs2 zoom

Wheel Base

The wheel base, or legs of the lifter, is the platform on which the lifting column is attached. This frame needs to be rigid and precise to ensure safety and good handling. Most people have experienced a damaged shopping trolley where one wheel vibrates and rattles due to the cart being bent. To avoid this kind of behaviour, the legs on our lifters are comprised entirely of steel and all joins fully welded. There are no weak aluminium or plastic parts and no screw connections that may become loose.

Control box zoom

Control unit and batteries

We have developed a custom made solid-state control unit for our 24V DC system that powers all our lifters. Where some systems use relays to control the large currents needed to drive the motor, our solution has no moving parts. This dramatically lowers the failure rate, resulting in a stable and reliable system.
Our standard, powerful battery packs have a capacity of  9, 18 or 45 Ah . This ensures, that for most applications, the lifter only needs to be charged once for every eight-hour shift.

Manual manipulators are lifting tools that in themselves can be turned, swung or otherwise moved by hand to help position the load.
Non-manipulators are simple lifting tools that support a load. Typically designed to accommodate a specific type of load, these tools are found in countless different versions.
Electrical manipulators are lifting tools that in themselves can be turned, swung or otherwise moved electrically to help position the load.